|
2008 RULE BOOK
For questions or clarification, please
contact Randy Varney
ENDURO
Full-size
1: Full size with a
minimum 106” wheel base.
Sedan
or station wagon, front or rear wheel drive.
No pick-ups, convertibles or all wheel drives allowed.
No leaf spring cars allowed.
Coil or strut suspension only.
2: Cars must be
completely stock. All
body panels must remain as manufactured.
No T-tops or sun roofs allowed.
3:
Front and rear bumpers must be chained to prevent dragging if
mount breaks. Cable may
be used.
4:
No anti-freeze allowed. Water
is the only allowed engine coolant.
It will be checked.
5:
Suspension – No modifications allowed.
All parts must be stock for make and model.
No spacers. No
cutting, heating or bending of any suspension allowed.
Camber limited to stock adjustments not to exceed 1 inch.
6:
Tires – Must be stock passenger tires only.
65, 70, or 75 series only.
No bias ply tires or retread tires are allowed.
No directional tires allowed.
All tires must have a readable treadwear of 360 or
numerically higher. All
four tires must be the same size.
Example: 205/75/14
7:
Wheels – Must be OEM stock wheels.
No aftermarket wheels allowed.
One inch lug nuts allowed.
8:
Engine – Must be stock for make and model.
Stock carb throttle body or fuel injection only.
Stock fuel pump only. No
after-market fuel systems allowed.
Battery
must remained in stock location and be secured and covered.
9:
Transmission and Driveline – Must be stocked for make and
model. No lock or
posi-trac differentials.
10:
Gas tank must be original stock position or secured in trunk.
Fuel cell or boat tank secured in trunk strongly recommended.
11:
Exhaust must extend to rear-seat area and secured to ground.
No exhaust may exit outside of the car.
12:
Driver protection bars are optional but recommend.
Roll bars or cage must be professionally welded but not
bisect or dissect any firewall.
13:
All doors must be welded or chained shut.
Hood and trunk latches must be removed.
Pull-pin hood pins must be used.
A ten-inch must be cut in center of hood.
14:
All glass lights in trim chrome and plastic must be removed.
Full-front windshield mandatory.
No badly cracked windshield allowed.
15:
Driver seat with seatbelt in shoulder strap required.
Three-point harness recommend.
All carpet and upholstery must be removed.
16:
Safety Equipment – Helmet with a minimum Snell 90 rating.
Long pants and sleeves required.
Driving suit and driving gloves recommended.
Must have window net mounted at bottom with quick release on
top.
Four-cylinder
1:
Max-wheel base 104.5. 4-Cylinder
engines only. No rear
engine, no mid-engine, or rotary engines allowed.
Sedans and wagons only. No
pick-ups, convertibles, or mini-vans allowed.
No t-tops or sun roofs allowed.
Sun roof must be removed and covered with minimum 22-guage
steel on top and bottom of opening.
2:
Cars must be completely stock.
Remo
val
of upholstery allowed. All
body panels must remain as manufactured.
No T-tops or sun roofs allowed.
3:
Front and rear bumpers must be chained to prevent dragging.
If mount breaks, cable may be used.
4:
No anti-freeze allowed. Water
is the only allowed engine coolant.
It will be checked.
5:
Suspension – No modifications allowed.
All parts must be stock for make and model.
No spacers. No
cutting, heating or bending of any suspension allowed.
Camber limited to stock adjustments not to exceed 1 inch.
6:
Tires – Must be stock passenger tires only.
60, 65, 70, or 75 series only.
No bias ply tires or retread tires are allowed.
No directional tires allowed.
All tires must have a readable treadwear of 360 or
numerically higher. All
four tires must be the same size.
Example: 205/75/14
7:
Wheels – Must be OEM stock wheels.
No aftermarket wheels allowed.
One inch lug nuts allowed.
8:
Engine – Must be stock for make and model.
Stock carb throttle body or fuel injection only.
Stock fuel pump only. No
after-market fuel systems allowed.
Battery
must remained in stock location and be secured and covered.
9:
Transmission and Driveline – Must be stocked for make and
model. No lock or
posi-trac differentials.
10:
Gas tank must be original stock position or secured in trunk.
Fuel cell or boat tank secured in trunk strongly recommended.
11:
Exhaust must extend to rear-seat area and secured to ground.
No exhaust may exit outside of the car.
12:
Driver protection bars are optional but recommend.
Roll bars or cage must be professionally welded but not
bisect or dissect any firewall.
13:
All doors must be welded or chained shut.
Hood and trunk latches must be removed.
Pull-pin hood pins must be used.
A ten-inch must be cut in center of hood.
14:
All glass lights in trim chrome and plastic must be removed.
Full-front windshield mandatory.
No badly cracked windshield allowed.
15:
Driver seat with seatbelt in shoulder strap required.
Three-point harness recommend.
All carpet and upholstery must be removed.
16:
Safety Equipment – Helmet with a minimum Snell 90 rating.
Long pants and sleeves required.
Driving suit and driving gloves recommended.
Must have window net mounted at bottom with quick release on
top.
.
|
